ZINC METAL SHOT

metal 

ZN; RTECS: ZG8600000

Emergency Overview 

Color:  gray 

Change in color: Not available

Physical Form: solid

Physical Hazards:  Negligible fire and explosion hazard in bulk form. Dust/air mixtures may ignite or explode. 

Short Term:  irritation, nausea, vomiting, diarrhea, difficulty breathing, headache 

Long Term:  digestive disorders 

Short Term:  irritation (possibly severe) 

Long Term:  no information on significant adverse effects 

Short Term:  irritation (possibly severe), tearing 

Long Term:  no information is available 

Short Term:  nausea, diarrhea, stomach pain, dizziness, hyperactivity or drowsiness, kidney damage 

Long Term:  hair loss, headache, hyperactivity, lung damage, kidney damage, liver damage 

This product may be regulated, have exposure limits or other information identified as the following: Zinc compounds.

If adverse effects occur, remove to uncontaminated area. Give artificial respiration if not breathing. If breathing is difficult, oxygen should be administered by qualified personnel. Get immediate medical attention. 

Wash skin with soap and water for at least 15 minutes while removing contaminated clothing and shoes. Get medical attention, if needed. Thoroughly clean and dry contaminated clothing and shoes before reuse. 

Flush eyes with plenty of water for at least 15 minutes. Then get immediate medical attention. 

If a large amount is swallowed, get medical attention. 

For inhalation, consider oxygen. 

See Section 9 for Flammability Properties 

Negligible fire hazard. Negligible fire and explosion hazard in bulk form. Dust/air mixtures may ignite or explode. 

dolomite, dry powder for metal fires, dry sand, graphite, soda ash, sodium chloride Do not get water directly on material. 

Move container from fire area if it can be done without risk. Cool containers with water spray until well after the fire is out. Stay away from the ends of tanks. For fires in cargo or storage area: Cool containers with water from unmanned hose holder or monitor nozzles until well after fire is out. If this is impossible then take the following precautions: Keep unnecessary people away, isolate hazard area and deny entry. Let the fire burn. Use extinguishing agents appropriate for surrounding fire. Avoid inhalation of material or combustion by-products. 

Collect spilled material in appropriate container for disposal. Keep out of water supplies and sewers. Keep unnecessary people away, isolate hazard area and deny entry. Notify Local Emergency Planning Committee and State Emergency Response Commission for release greater than or equal to RQ (U.S. SARA Section 304). If release occurs in the U.S. and is reportable under CERCLA Section 103, notify the National Response Center at (800)424-8802 (USA) or (202)426-2675 (USA). 

Store and handle in accordance with all current regulations and standards. Keep separated from incompatible substances. 

Component Exposure Limits 

Biological limit value 

Provide local exhaust ventilation system. Ventilation equipment should be explosion-resistant if explosive concentrations of material are present. Ensure compliance with applicable exposure limits. 

Eyes/Face Wear splash resistant safety goggles. Provide an emergency eye wash fountain and quick drench shower in the immediate work area. 

Wear appropriate chemical resistant clothing. 

Wear appropriate chemical resistant gloves. 

The following respirators and maximum use concentrations are drawn from NIOSH and/or OSHA. 50 mg/m3 Any particulate respirator equipped with an N95, R95, or P95 filter (including N95, R95, and P95 filtering facepieces) except quarter-mask respirators. The following filters may also be used: N99, R99, P99, N100, R100 or P100. Any supplied-air respirator. 125 mg/m3 Any supplied-air respirator operated in a continuous-flow mode. Any powered, air-purifying respirator with a high-efficiency particulate filter. 250 mg/m3 Any air-purifying, full-facepiece respirator equipped with an N100, R100, or P100 filter. Any supplied-air respirator with a tight-fitting facepiece that is operated in a continuous-flow mode. Any powered, air-purifying respirator with a tight-fitting facepiece and a high-efficiency particulate filter. Any self-contained breathing apparatus with a full facepiece. Any supplied-air respirator with a full facepiece. 500 mg/m3 Any supplied-air respirator operated in a pressure-demand or other positive-pressure mode. Emergency or planned entry into unknown concentrations or IDLH conditions - Any self-contained breathing apparatus that has a full facepiece and is operated in a pressure-demand or other positive-pressure mode. Any supplied-air respirator with a full facepiece that is operated in a pressure-demand or other positive-pressure mode in combination with an auxiliary self-contained breathing apparatus operated in pressure-demand or other positive-pressure mode. Escape - Any air-purifying, full-facepiece respirator equipped with an N100, R100, or P100 filter. Any appropriate escape-type, self-contained breathing apparatus. For Unknown Concentrations or Immediately Dangerous to Life or Health - Any supplied-air respirator with a full facepiece that is operated in a pressure-demand or other positive-pressure mode in combination with an auxiliary self-contained breathing apparatus operated in pressure-demand or other positive-pressure mode. Any self-contained breathing apparatus that has a full facepiece and is operated in a pressure-demand or other positive-pressure mode. 

acids, alkali, acetic acid 

Stable at normal temperatures and pressure. 

None reported. 

acids, bases, metals, oxidizing materials, reducing agents, halo carbons, metal salts, halogens, combustible materials, amines, metal oxides, 

ZINC: ACIDS: Evolves hydrogen gas which may be ignited by the heat of the reaction ALKALIES: Evolves hydrogen gas which may be ignited by the heat of the reaction. ALUMINUM (POWDER): Possible ignition. ALUMINUM-MAGNESIUM ALLOY + RUSTED STEEL: May spark on impact. AMMONIUM NITRATE: Violent reaction or formation of explosive mixture. AMMONIUM SULFIDE: May explode in a closed container. ARSENIC: Incandescent reaction when heated. ARSENIC TRIOXIDE: Explosive reaction on heating. BROMOMETHANE: Forms flammable compounds. CADMIUM: Incandescent reaction. CALCIUM CHLORIDE: Evolves hydrogen gas which may be ignited by the heat of the reaction. CARBON DISULFIDE: Incandescent reaction. CARBON TETRACHLORIDE + METHANOL: Extremely vigorous reaction. CHLORATES: Forms shock-sensitive mixtures. CHLORINATED RUBBER: Violent or explosive reaction at elevated temperatures. CHROMIC ANHYDRIDE: Violent reaction and possible ignition. COBALT HALIDE (METHANOLIC SOLUTION) + IRON PENTACARBONYL: Violent reaction. ETHYL ACETOACETATE + TRIBROMONEOPENTYL ALCOHOL: May react explosively. HALOCARBONS: Possible violent reaction with ignition. HALOGENS: Possible ignition. HYDRAZINE NITRATE: Ignites on warming. HYDROXYLAMINE: May ignite or explode when heated. INTERHALOGENS: Violent reaction and possible ignition. LEAD AZIDE: Increased sensitivity to explosive decomposition. MANGANESE DICHLORIDE: Explosive reaction when heated. METAL OXIDES: Possible ignition or incandescent reaction. NITRIC ACID: Incandescent reaction. 2-NITROANISOLE + SODIUM HYDROXIDE: Exothermic reaction. NITROBENZENE: May form pyrophoric residue. NITRYL FLUORIDE: Incandesces when warmed. OXIDIZERS (STRONG): Fire and explosion hazard. PEROXYFORMIC ACID: Violent explosion on contact. POTASSIUM NITRATE: Explosive reaction on heating. POTASSIUM PEROXIDE: Incandescent reaction. RHODIUM HALIDES (METHANOLIC SOLUTION) + IRON PENTACARBONYL: Violent reaction. RUTHENIUM HALIDES (METHANOLIC SOLUTION) + IRON PENTACARBONYL: Violent reaction. SELENIUM: Incandescent reaction. SELENINYL BROMIDE: Ignition. SILVER + ELECTROLYTES (BATTERIES): May spontaneously combust. SODIUM PEROXIDE: Incandescent reaction. SULFUR: Violent reaction. TELLURIUM: Incandescent reaction. ZINC CHLORIDE: May increase flammability.

oxides of zinc 

Thermal decomposition products: zinc oxide.

Will not polymerize. 

Component Analysis - LD50/LC50 

Component Carcinogenicity

None of this product's components are listed by ACGIH, IARC, NTP, DFG or OSHA

respiratory disorders, skin disorders and allergies, 

Excessive zinc intake has been associated with a copper-deficiency anemia. 

ZINC: Inhalation of dust may cause irritation with difficulty in breathing and sneezing Neurological and psychiatric symptomology including irritability, upper extremity coarse intention tremor, incoordination, and ataxia have also been reported Metal fume fever, an influenza-like illness, may occur due to the inhalation of freshly formed metal oxide particles sized below 1.5 microns and usually between 0.02-0.05 microns Symptoms may be delayed 4-12 hours and begin with a sudden onset of thirst, and a sweet, metallic, or foul taste in the mouth Other symptoms may include upper respiratory tract irritation accompanied by coughing and a dryness of the mucous membranes, lassitude, and a generalized feeling of malaise Fever, chills, muscular pain, mild to severe headache, nausea, occasional vomiting, exaggerated mental activity, profuse sweating, excessive urination, diarrhea, and prostration may also occur Tolerance to fumes develops rapidly, but it is quickly lost All symptoms usually subside within 24-36 hours.

ZINC Severe gastrointestinal disturbances and hypochromic anemia have been reported, but other chemicals may have contributed to the effects.

ZINC: Dust may cause mechanical irritation and mild dermatitis in intertriginous areas Reaction with moisture on skin may result in serious burns.

ZINC: 300 ug applied to human skin intermittently for 3 days caused mild irritation Allergic reactions are rare, but have been reported.

ZINC: Dust may cause mechanical irritation or injury to the surface of the eye, with discomfort, reddening, and tearing Direct contact may cause serious corneal burns.

ZINC No data available.

ZINC: Large oral doses may cause gastrointestinal distress with stomach cramps, dehydration, electrolyte imbalance, abdominal pain, nausea, vomiting, hematemesis, diarrhea, lethargy, immune system effects, fever, dizziness, tightness in the throat, shock, collapse, renal failure, and death Survivors may have residual nephritis and strictures of the esophagus and pyloric end of the stomach.

ZINC: Patients taking zinc in amounts 10 times the RDA for months and years have not shown any adverse reactions Excessive absorption may cause copper-deficiency anemia Ingestion of approximately 85.7 mg/kg/day for 2 days caused lethargy, lightheadedness, staggering, and difficulty in writing clearly 2 people who ingested 40 ppm in drinking water for several months experienced lack of concentration, drowsiness, mental and physical fatigue, pain in the arms and legs, headache, stiffness, muscle pains, loss of appetite, nausea, weight loss, and lassitude 90 ppm in the diet for 5 weeks has resulted in a decrease in the HDL cholesterol level Pancreatic abnormalities have also been observed A diet of 0.25% in rats caused no injury; above 0.25% there was breakdown of the homeostatic mechanism, growth retardation, hypochromic anemia, and defective mineralization of the bones Mice fed 500 ppm for 14 months exhibited hypertrophy of the adrenal cortex and changes indicating hyperactivity of the pancreatic islets and pituitary gland; 30,000 ppm for 13 weeks caused liver and kidney damage and some deaths Cows fed 2% for 2 days developed severe enteritis, with 7 of 40 dying Severe pulmonary emphysema and changes in the myocardium, kidneys, and liver were observed Pigs fed >1000 ppm had reduced food intake and weight gain; at >2000 ppm, death occurred after 2 weeks Bone changes were observed in foals fed 5400 ppm High dietary levels of zinc have been associated with reduced fetal weights, altered concentrations of fetal iron and copper, and alopecia and reduced growth of offspring in animals.

Component Analysis - Aquatic Toxicity 

Dispose in accordance with all applicable regulations. 

Component Waste Numbers 

ADR Tunnel Code Restrictions 

Component Marine Pollutants (IMDG) 

SARA Section 311/312 (40 CFR 370 Subparts B and C) 

Not listed under California Proposition 65 

Germany Water Classification 

The listed component(s) of this material have been checked for country-specific published classifications according to the Globally Harmonized System of Classification and Labeling (GHS). The results of the queries are displayed below. Please see the individual country listings, as additional interpretations or reference information may be available. For a reference list of H- or P-statements, please visit ChemADVISOR’s website at http://www.chemadvisor.com/product-resources/26-pure-substance-and-mixture-databases/247-ghs-hazard-and-physical-statements 

Australia GHS Classifications 

Australia GHS Labeling Information 

European Union GHS Classifications 

Indonesia GHS Classifications 

Japan GHS Classifications 

Japan GHS Labeling Information 

Korea GHS Classifications 

Korea GHS Labeling Information 

New Zealand GHS Classifications 

New Zealand GHS Labeling Information 

South Africa GHS Classifications 

Taiwan GHS Classifications 

Taiwan GHS Labeling Information 

No classification assigned. 

ACGIH - American Conference of Governmental Industrial Hygienists; ADR - European Road Transport; AU - Australia; BOD - Biochemical Oxygen Demand; C - Celsius; CA - Canada; CAS - Chemical Abstracts Service; CERCLA - Comprehensive Environmental Response, Compensation, and Liability Act; CN - China; CPR - Controlled Products Regulations; DFG - Deutsche Forschungsgemeinschaft; DOT - Department of Transportation; DSL - Domestic Substances List; EEC - European Economic Community; EINECS - European Inventory of Existing Commercial Chemical Substances; EPA - Environmental Protection Agency; EU - European Union; F - Fahrenheit; IARC - International Agency for Research on Cancer; IATA - International Air Transport Association; ICAO - International Civil Aviation Organization; IDL - Ingredient Disclosure List; IDLH - Immediately Dangerous to Life and Health; IMDG - International Maritime Dangerous Goods; JP - Japan; Kow - Octanol/water partition coefficient; KR - Korea; LEL - Lower Explosive Limit; LOLI - List Of LIsts™ - ChemADVISOR’s Regulatory Database; MAK - Maximum Concentration Value in the Workplace; MEL - Maximum Exposure Limits; NFPA - National Fire Protection Agency; NIOSH - National Institute for Occupational Safety and Health; NJTSR - New Jersey Trade Secret Registry; NTP - National Toxicology Program; NZ - New Zealand; OSHA - Occupational Safety and Health Administration; PH - Philippines; RCRA - Resource Conservation and Recovery Act; RID - European Rail Transport; RTECS - Registry of Toxic Effects of Chemical Substances®; SARA - Superfund Amendments and Reauthorization Act; STEL - Short-term Exposure Limit; TDG - Transportation of Dangerous Goods; TSCA - Toxic Substances Control Act; TWA - Time Weighted Average; UEL - Upper Explosive Limit; US - United States 

Reasonable care has been taken in the preparation of this information; however, the manufacturer makes no warranty whatsoever including the warranty of merchantability, expressed or implied, with respect to this information. The manufacturer makes no representations and assumes no liability for any direct, incidental, consequential, or other such damages resulting from its use or misuse. 

Supplier gives no warranty whatsoever, including the warranties of merchantability or of fitness for a particular purpose. Any product purchased is sold on the assumption the purchaser shall determine the quality and suitability of the product. Supplier expressly disclaims any and all liability for incidental, consequential or any other damages arising out of the use or misuse of this product. No information provided shall be deemed to be a recommendation to use any product in conflict with any existing patent rights. THIS SDS IS TO BE UTILIZED SOLELY AS A REFERENCE DOCUMENT AND IT IS NOT TO BE USED TO SATISFY THE DISTRIBUTION REQUIREMENTS OF OSHA'S HAZARD COMMUNICATION STANDARD (HCS) NOR CANADA'S CONTROLLED PRODUCT REGULATION (CPR). Read the Safety Data Sheet before handling product. Use of any information contained herein is provided at the reader's own risk and thus independent judgment by trained professionals must be utilized at all times. 

Copyright 1984-2016 ChemADVISOR, Inc "RTECS®" is a United States trademark owned and licensed under authority of the U.S. Government, by and through Accelrys/Biovia. Portions ©Copyright 2016, U.S. Government. All rights reserved